 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Model PD1722J5050S2 Rev A Ultra Low Profile 0805 Power Divider 50 to 50 Description The PD1722J5050S2 is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD1722J5050S2 is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD1722J5050S2 is matched to 50 and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: WCDMA, and GSM, The PD1722J5050S2 does not include the resistive element and therefore, requires an external resistor for operation. The PD1722J5050S2 is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25C) * * * * * * * * * * Features: 1700-2200 MHz 15 dB Isolation (output ports) 0.5mm Height Profile 50 Input / 50 Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant External resistor required Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature Min. 1700 Typ. 50 50 13 0.6 0.1 1 18 Max 2200 10 0.8 0.3 3 2 +85 15 -55 Unit MHz dB dB dB Degrees dB Watts C * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 C) Outline Drawing Top View (Near-side) .079.004 [2.000.10] Side View Bottom View (Far-side) 2X .026 [0.65] .039 [0.98] 1 2 3 6X .009 [0.22] .021.002 [0.530.05] .049.004 [1.250.10] Orientation Marker Denotes Pin Location Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation GND Input GND Output 1 GND Output 2 6 5 6X .012 [0.30] 4 Dimensions are in Inches [Millimeters] Mechanical Outline Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD1722J5050S2 Rev A Typical Broadband Performance: 500 MHz. to 6.0 GHz. Return Loss - Input 0 -3 -6 -9 -12 -15 [dB] Insertion Loss 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] deg Phase Balance 20 15 10 5 0 -5 -10 -15 -20 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 0 -0.5 -1 -1.5 -2 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Frequency [MHz] USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. 6000 Model PD1722J5050S2 Rev A Typical Performance: 1700 MHz. to 2200 MHz. Return Loss - Input 0 -3 -6 -9 -12 -15 [dB] Insertion Loss 0.0 -0.3 -0.6 -0.9 -1.2 -1.5 [dB] -18 -21 -24 -27 -30 -33 -36 1700 1800 1900 2000 2100 2200 -1.8 -2.1 -2.4 -2.7 -3.0 -3.3 -3.6 1700 1800 1900 2000 2100 2200 2200 Frequency [MHz] Frequency [MHz] Amplitude Balance 2 1.5 1 0.5 [dB] deg Phase Balance 20 15 10 5 0 -5 -10 -15 -20 1700 1800 1900 2000 0 -0.5 -1 -1.5 -2 1700 1800 1900 2000 2100 2200 Frequency [MHz] Frequency [MHz] Isolation 0 -3 -6 -9 -12 -15 [dB] -18 -21 -24 -27 -30 -33 -36 1700 1800 1900 2000 2100 2200 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 2100 Model PD1722J5050S2 Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD1722J5050S2 is a Wilkinson power divider, an external 0603 100 resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. Pad Footprint w/ 0603 Resistor Locations 3X Transmission Line 6X .016 [0.35] 4X .010 [0.25] Plated thru holes to ground 6X .013 [0.33] .026 [0.66] 6X .002 [0.05] R1 Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model PD1722J5050S2 Rev A Packaging and Ordering Information Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. OA OC OD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) OA 7.00 [177.8] B 0.32 [8.0] OC 2.0 [50.8] OD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 |
Price & Availability of PD1722J5050S2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |